HAMCO manufactures dip-moulded edge protection caps for custom profile cross-sections. The inner contour of the caps is determined by the geometry of the dip mould and tailored to the profile to be protected.
The required wall thickness depends on the specific profile geometry and the demouldability of the edge protection cap. It is determined during the sampling process.
Where the profile geometries are suitable, HAMCO can use the original profile as the raw material for the production of the dip cores. To this end, the customer supplies unperforated bar stock, which HAMCO then cuts to length and machines itself in its own toolmaking department in accordance with the manufacturing requirements.
The internal contour of the edge protection caps is determined by the geometry of the moulding cores. The subsequent shrinkage of the PVC results in the desired undersize, which ensures a secure, non-detachable fit on the profile.
There must be no cut-outs or drill holes in the immersed core, such as those found in cable support profiles to reduce weight. In the case of hollow-chamber profiles, the hollow chambers may be sealed in order to simplify the internal geometry of the edge protection caps.
As they are undersized, the edge protection caps sit on the profile to be protected with a slight pre-tension. To make fitting easier, the caps can be heated to up to 50 °C if necessary. This makes the PVC more flexible and allows it to be slid onto the profile more easily.
The hardness of the material also affects how it behaves during assembly. Softer versions are easier to expand, whilst harder versions have greater inherent rigidity and retain their shape better when slipped onto the shaft. The appropriate hardness depends on the specific profile geometry and the requirements for assembly and retention.
When processing soft PVC using dip and coating processes, HAMCO utilises a salt-free heat transfer system. No salt-containing heat transfer media, such as lithium or potassium nitrate, are used. This ensures that no residues of these salts remain on the manufactured or coated components. This is particularly important in applications where users come into contact with the components and any salt residues could pose a health risk.
With Outdoor applications exposed to the elements Colour must be taken into account when selecting materials. Dark shades already exhibit a certain degree of better UV resistance rather than light colours. However, for long-term use in exposed outdoor conditions, the formulation should can also be optimised for dark shades by adding a UV stabiliser.
In the case of light colours, particular attention should be paid to this additional UV optimisation due to their lower UV resistance.
As both the PVC plastisol and the UV stabiliser used have their own inherent colour, the resulting shade may be slightly affected. HAMCO therefore confirms that the shades are similar to the respective RAL colour.
HAMCO manufactures the dip-moulded edge protection caps from soft PVC in the Covytec® range. The standard material used is Covytec® 6691, which has a hardness of 71 Shore A.
Depending on requirements, further material variants and hardness grades are available. These include, amongst others, phthalate-free versions and those suitable for medical applications, as well as materials with special properties in terms of UV resistance, ESD or detectability.
Further technical details on the standard material can be found in the Covytec® 6691 Material Data Sheet.
The Wall thickness is measured non-destructively at the open end of the submerged section. Due to the nature of the process, it increases continuously towards the closed end.
Drain marks and drain drops At the closed end, they cannot be completely avoided due to the nature of the process.
How elastic dip-moulded parts are produced from liquid PVC plastisol, and which factors influence their properties and dimensions.
HAMCO manufactures and machines bespoke dip-moulding tools in its in-house toolmaking department for the production of custom PVC dip-moulded parts. Find out more about what we can offer.
Answers to frequently asked questions about plastics processing at HAMCO.
Technical concepts explained in an accessible way – with a high standard of technical rigour and a slightly different perspective on plastics and their properties.
Do you need an edge protector for a specific profile? To assess your enquiry, we require the following details:
Please also provide us with a sample of the profile. We will use this sample to assess the technical feasibility of production and the options for manufacturing the required dip moulds.
If the original profile is to be used as the raw material for the dip-moulded cores, we require solid bar stock when an order is placed. We cut this to length ourselves in accordance with the manufacturing requirements and machine it for use in the dip-moulding process.
Large and small quantity requirements Direct processing
Large and small quantity requirements
You are currently viewing a placeholder content from Vimeo. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
More InformationYou are currently viewing a placeholder content from YouTube. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
More InformationYou need to load content from reCAPTCHA to submit the form. Please note that doing so will share data with third-party providers.
More Information