Ball handle, dipped, for round profiles

Material: PVC
  • sturdy
  • Durable
  • ergonomically shaped
  • Easy to install
  • loss-proof
  • economic
  • Standardised sizes
Round profile ball handle

Type of execution

Tolerances:

  • Height H: ± 2.0 mm
  • Wall thickness s: ± 0.25 mm

The required minimum wall thickness at the open end depends on the diameter of the handle in question. The minimum wall thicknesses for the available standard dimensions are specified in the product table.

Article features

We have summarised the key features of our dipped ball handles for round profiles for you:

  • Ergonomic grip shape with a pronounced ball contour
  • A surface that is pleasantly non-slip and elastic
  • Retains its shape whilst offering sufficient flexibility
  • A secure fit thanks to under-dimensioned manufacturing
  • Suitable for round tubes and round sections
  • Various standard dimensions and handle lengths as per the product table
  • Manufacturing without tool separation seam and burr formation
  • Free product samples for most sizes are available from stock

Application examples

HAMCO’s dip-coated ball handles are used in a variety of industrial, commercial and medical-technical applications. Typical examples include:

  • Hand tools
  • Control levers and operating elements
  • Gripping systems on machinery and plant
  • Clamping and fastening tools
  • Transport equipment and lifting systems
  • Fitness and sports equipment
  • Medical devices
  • Rehabilitation and orthopaedic products

Special Covytec® material grades are available for applications in medical and orthopaedic technology. Their suitability must be assessed on the basis of the relevant requirements and operating conditions.

Selection and fitting of bale handles

The dip-coated PVC bale handles are manufactured slightly undersized and slipped onto the round tube or round profile. During installation, the flexible material stretches and then moulds itself to the outer contour of the round profile. The resulting restoring forces and static friction ensure that the bale handle sits securely and cannot come loose.

The product table shows which handle size is intended for each pipe diameter. Within the range specified there, the desired handle height H can be selected.

If the installation forces are high, gently heating the ball handle to around 50 °C can make installation easier. Alternatively, standard window cleaner can be applied or sprayed onto the round tube or the inside of the ball handle. It forms a temporary lubricating film which makes it easier to slide the handle on; once dry, it loses its lubricating effect.

For versions made from harder materials, installation may be more difficult due to the material’s lower flexibility. At the same time, the higher hardness can improve the grip of the fitted bale handle. The most suitable material hardness therefore also depends on the installation conditions and the requirements for subsequent use.

Where there are specific requirements for long-term hold, additional bonding may be advisable. This requires the use of an adhesive suitable for the PVC material in question and the material of the round profile. The suitability of the bonded joint must be checked under the intended conditions of use..

Free from residues of saline heat transfer fluids

When processing soft PVC using dip and coating processes, HAMCO utilises a salt-free heat transfer system. No salt-containing heat transfer media, such as lithium or potassium nitrate, are used. This ensures that no residues of these salts remain on the manufactured or coated components. This is particularly important in applications where users come into contact with the components and any salt residues could pose a health risk.

Available colours

HAMCO Standard colours
WhiteRAL 9010*
BlackRAL 9005*
GreyRAL 7001*
GreenRAL 6002*
BlueRAL 5017*
RedRAL 3000*
OrangeRAL 2009*
YellowRAL 1021*
Natural-transparent*
Grey whiteRAL 9002*
Mahogany brownRAL 8016*
Green-brownRAL 8000*
Light greyRAL 7035*
Pebble greyRAL 7032*
Black greyRAL 7021*
Anthracite greyRAL 7016*
Signal greenRAL 6032*
Mint greenRAL 6029*
Opal greenRAL 6026*
Yellow greenRAL 6018*
May greenRAL 6017*
Blue-greenRAL 6004*
Water blueRAL 5021*
Turquoise blueRAL 5018*
Pigeon blueRAL 5014*
Cobalt blueRAL 5013*
Light blueRAL 5012*
Gentian blueRAL 5010*
Traffic laneRAL 4006*
Blue purpleRAL 4005*
Erika violetRAL 4003*
Red purpleRAL 4001*
Light pinkRAL 3015*
Ruby redRAL 3003*
Traffic orangeRAL 2009*
Traffic yellowRAL 1023*
Zinc yellowRAL 1018*
Sulphur yellowRAL 1016*
Brown beigeRAL 1011*

With Outdoor applications exposed to the elements Colour must be taken into account when selecting materials. Dark shades already exhibit a certain degree of better UV resistance rather than light colours. However, for long-term use in exposed outdoor conditions, the formulation should can also be optimised for dark shades by adding a UV stabiliser.

In the case of light colours, particular attention should be paid to this additional UV optimisation due to their lower UV resistance.

As both the PVC plastisol and the UV stabiliser used have their own inherent colour, the resulting shade may be slightly affected. HAMCO therefore confirms that the shades are similar to the respective RAL colour.

Material

To manufacture the dipped bale handles, HAMCO uses soft PVC from the Covytec® material series. The standard material used is Covytec® 6691, which has a hardness of 71 Shore A.

Further Covytec® material variants allow for different hardness settings and adaptation to the specific requirements of various industries and applications. These include, for example, phthalate-free, ESD-compatible or detectable material variants, as well as material variants for medical applications and versions with enhanced UV stabilisation.

Important quality information

The Wall thickness is measured non-destructively at the open end of the submerged section. Due to the nature of the process, it increases continuously towards the closed end.

Drain marks and drain drops At the closed end, they cannot be completely avoided due to the nature of the process.

Further information

Technical articles on the HAMCO blog

On the HAMCO blog, the company regularly publishes specialist articles on plastics, manufacturing, applications and technical issues.

FAQ – Frequently Asked Questions

Answers to frequently asked technical questions about plastics, materials, manufacturing processes and their applications.

Immersion process

How elastic dip-moulded parts are produced from liquid PVC plastisol, and which factors influence their properties and dimensions.

Plastic firecracker

Technical concepts explained in an accessible way – with a high standard of technical rigour and a slightly different perspective on plastics and their properties.

Your enquiry to HAMCO

Please select the appropriate version from the product table below based on the external diameter of your round tube or round profile.

To ensure your enquiry is dealt with promptly, we require the following details:

  • Outer diameter of the round tube or round section
  • Desired handle height H
  • Preferred colour
  • Quantity required
  • Any specific requirements regarding the handle or the material

In the case of special installation scenarios or geometries that differ from the standard designs, you can also provide us with a drawing or a sample of the component.

Product table

KindØ nominal dimension
[mm]
Length L min.
[mm]
Length L max.
[mm]
Wall thickness min. [mm]Suitable for Ø
[mm]
RD - Ball handle11.5901101.612 - 13,5
RD - Ball handle181001251.818,5 - 20
RD - Ball handle211101251.821,5 - 23
RD - Ball handle221101301.822,5 - 24
RD - Ball handle241001251.824,5 - 26

Ball handle, dipped, for round profiles - Enquire now

Supplier to the industry

Large and small quantity requirements Direct processing

Supplier to the technical trade

Large and small quantity requirements

Note on mandatory fields and data protectionThe mandatory field is marked. All other fields are voluntary. Your data will only be collected and stored electronically strictly for the purpose of processing and answering your enquiry. Information on data processing can be found here: Data protection.
Permitted file formats: pdf, jpg, dxf, stp, step, igs, tif, dwg, zip, jpeg (max. 6MB per file)